Compressed heat zero gas consumption adsorption dryer

Compressed heat zero gas consumption adsorption dryer
Model	Air handling capacity Nm³/min	Interface size	Cooling water inlet and outlet	Outline sizemm			power	weight(KG)	water consumption
				L	W	H	（Kw）		T/h
HBYADZ-40	40	DN100	DN80	3100	1500	2430	0.25	3800	28
HBYADZ-50	50	DN100	DN80	3200	1700	2780	0.25	4550	34.6
HBYADZ-75	75	DN125	DN80	3500	1900	3050	0.25	5850	52
HBYADZ-90	90	DN150	DN100	3950	2100	3375	0.25	7500	64
HBYADZ-100	100	DN150	DN100	3950	2100	3375	0.25	7600	70
HBYADZ-125	125	DN150	DN100	4250	2300	3250	0.25	9050	86
HBYADZ-150	150	DN200	DN125	4250	2300	3250	0.25	10050	104
HBYADZ-180	180	DN200	DN125	4750	2310	3570	0.25	13000	125
HBYADZ-200	200	DN200	DN125	4750	2310	3570	0.25	13500	140
HBYADZ-230	230	DN200	DN125	5100	2800	3700	0.25	15500	160
HBYADZ-250	250	DN200	DN125	5100	2800	3700	0.25	15700	173
HBYADZ-280	280	DN250	DN125	5400	3200	3820	0.25	19300	196
HBYADZ-300	300	DN250	DN125	5550	3200	3820	0.25	18480	204
HBYADZ-330	330	DN250	DN125	6100	3350	3790	0.25	23000	222
HBYADZ-350	350	DN250	DN125	6100	3400	3820	0.25	24500	242
HBYADZ-460	460	DN300	DN125	5420	5695	3600	0.25	25500	320
HBYADZ-550	550	DN350	DN150	5420	5695	3600	0.25	25500	380
HBYADZ-650	650	DN350	DN150	5800	5900	3600	0.25	30000	450

Product principle introduction:
The compressed heat zero gas consumption adsorption dryer uses the high-temperature heat energy discharged from the air compressor to carry out deep desorption and regeneration of the adsorbent, cancels the external electric heater, and there is no regeneration gas consumption when heating. When cooling, the high-temperature compressed air is cooled by the secondary cooler, and then the adsorbent is cooled again, so that the adsorbent has adsorption conditions, and there is no compressed gas emission during operation, which is the most economical Energy adsorption dryer.
Standard technical parameters:
1. Air inlet temperature: 120-200 ℃
2. Inlet pressure: 0.7-1.0mpa
3. Air dew point: - 40 ℃
4. Regeneration gas consumption: 0%
5. Ambient temperature: ≤ 45 ℃
6. Cooling water temperature 0-32 ℃
7. Cooling water pressure: 0.2-0.55mpa
8. Regular 8-hour cycle
8. Installation method: indoor, without foundation, concrete ground leveling, reserved maintenance and operation space
9. Adsorbent: activated alumina, molecular sieve
10. Power supply: 220-1ph-50hz
11. Users can optionally configure customized products, and consult our technical service department for detailed technical parameters
Design features:
1. Pure logic control, friendly human-machine interface, automatic continuous display of double tower working condition
2. It adopts high temperature resistant double eccentric pneumatic butterfly valve, stainless steel anti-corrosion valve body and stem, with long service life, valve position maintenance, fault alarm and feedback functions
3. The supporting ceramic ball is used at the bottom of the adsorption tower, which makes the air distribution more uniform, effectively prevents the failure of the adsorbent bubble water and prolongs the service life of the adsorbent
4. Scientific air distributor to reduce pressure loss, high utilization rate of desiccant and low risk of wear
5. The stainless steel cooler has good cooling effect and strong corrosion resistance.
6. The centrifugal gas-liquid separator has good separation effect and small pressure loss
7. Manual drainage and intelligent drainage system
8. Complete set of stainless steel power supply pipeline is provided as standard
9. Frequency conversion with delayed adsorption technology is more energy-saving (optional)
10. PLC control system has RS485 serial communication interface, which can meet the communication requirements of users (optional)