Zero gas consumption micro heat adsorption dryer

Model	Air handling capacity(Nm3/min)	Diffuser model	Interface size	Outline size（mm）			Weight（KG)
				L	W	H
HBHAD-4	4.5	KS-40	G1-1/2”	1100	550	1710	160
HBHAD-6	6.2	KS-40	G1-1/2”	1100	550	2080	350
HBHAD-8	8.5	KS-50	G2”	1300	650	2110	430
HBHAD-10	11	KS-50	G2”	1300	650	2110	460
HBHAD-13	13.5	KS-50	G2”	1350	700	2150	520
HBHAD-15	17	KS-65	DN65	1350	750	2270	720
HBHAD-20	22	KS-65	DN65	1400	750	2285	890
HBHAD-25	27	KS-80	DN80	1450	750	2545	950
HBHAD-30	32	KS-80	DN80	1450	775	2555	1320
HBHAD-40	42	KS-100	DN100	1700	925	2595	1550
HBHAD-50	50	KS-100	DN100	1800	950	2700	1800
HBHAD-60	65	KS-100	DN100	1850	975	2700	2250
HBHAD-80	85	KS-125	DN125	2100	1030	2810	2810
HBHAD-100	110	KS-150	DN150	2600	1200	3020	4150
HBHAD-130	140	KS-150	DN150	2700	1200	3030	4980
HBHAD-150	160	KS-200	DN200	2950	1400	3250	6250
HBHAD-180	185	KS-200	DN200	3250	1450	3450	6460
HBHAD-200	210	KS-200	DN200	3600	1600	3500	7280
HBHAD-230	240	KS-200	DN200	3700	1700	3600	8520
HBHAD-250	260	KS-200	DN200	4000	1800	3800	9360

Product principle introduction:
The heatless adsorption dryer uses the principle of pressure swing adsorption to make the dryer adsorb under the pressure of pipe network, then desorb under the switch to atmospheric pressure, and lead about 12-14% of the dry product gas from the outlet of the dryer to further purify and regenerate the desiccant. The two towers alternately carry out the above process to provide dry compressed air to the gas consumption point.
Standard technical parameters:
1. Rated air inlet temperature: ≤ 40 ℃
2. Rated working pressure: 0.6-1.0mpa
3. Ambient temperature: ≤ 45 ℃
4. Air dew point: - 40 ℃ (0.7MPa) (customized below - 60 ℃)
5. Regeneration gas consumption: 12-14%
6. Pressure loss: ≤ 0.02MPa
7. Oil content of intake air: ＜ 0.1mg/m3
8. Installation method: indoor, without foundation, concrete ground leveling, reserved maintenance and operation space
9. Adsorbent: activated alumina, molecular sieve
10. Power supply: 220-1ph-50hz
11. Users can optionally configure customized products
Consult our technical service department for detailed technical parameters
Design features:
1. Short cycle adsorption cycle, isothermal operation, preservation of adsorption heat, good natural desorption effect
2. Full electronic programmable controller, friendly human-machine interface, automatic continuous display of double tower working condition
3. Regenerative orifice technology to effectively control regeneration flow
4. Accurate action, stable performance and simple operation
5. The inner wall of the cylinder shall be subject to professional antirust treatment, and shall not be rusted for 10 years
6. Stainless steel diffuser is corrosion-resistant, wear-resistant and durable
6. The stainless steel valve works stably, and its service life is up to 500000 times
7. Optimize the valve form to ensure the feasibility and convenience of on-site maintenance and replacement
8. Large flow muffler, lower back pressure, no condensation in muffler and exhaust channel
9. Frequency conversion with delayed adsorption technology is more energy-saving (optional)