| Model | Air handling capacity Nm³/min | Interface size | Cooling water inlet and outlet | Outline sizemm | power | weight(KG) | water consumption |
| L | W | H | （Kw） | T/h |
| HBYAD-25 | 25 | DN80 | DN50 | 2800 | 1750 | 2700 | 0.25 | 2600 | 8.7 |
| HBYAD-50 | 50 | DN100 | DN50 | 3100 | 1750 | 2790 | 0.25 | 3940 | 17.3 |
| HBYAD-75 | 75 | DN125 | DN80 | 3400 | 1850 | 3215 | 0.25 | 4890 | 26 |
| HBYAD-100 | 100 | DN150 | DN100 | 3650 | 2100 | 3215 | 0.25 | 6260 | 35 |
| HBYAD-125 | 125 | DN150 | DN100 | 3700 | 2400 | 3200 | 0.25 | 9700 | 43 |
| HBYAD-150 | 150 | DN150 | DN100 | 4000 | 2500 | 3260 | 0.25 | 10935 | 52 |
| HBYAD-180 | 180 | DN200 | DN100 | 4600 | 2700 | 3700 | 0.25 | 12200 | 62.5 |
| HBYAD-200 | 200 | DN200 | DN125 | 4600 | 2700 | 3700 | 0.25 | 13200 | 70 |
| HBYAD-230 | 230 | DN200 | DN125 | 4700 | 2750 | 3750 | 0.25 | 13800 | 80 |
| HBYAD-250 | 250 | DN200 | DN125 | 4700 | 2800 | 3800 | 0.25 | 17275 | 86.5 |
| HBYAD-280 | 280 | DN250 | DN150 | 5000 | 3250 | 3865 | 0.25 | 18000 | 98 |
| HBYAD-330 | 330 | DN250 | DN150 | 5200 | 3300 | 4000 | 0.25 | 21000 | 111 |
Product principle introduction:
The compressed heat adsorption dryer is a new type of compressed air with energy saving effect. It uses the high-temperature heat energy from the air compressor to carry out deep desorption and regeneration of the adsorbent, cancels the external electric heater, and there is no regeneration gas consumption when heating. When cooling the desiccant, a small amount of finished product dry compressed air is used for cooling, so that the desiccant has adsorption conditions and greatly saves energy consumption Air dryer.
Standard technical parameters:
1. Air inlet temperature: 120-200 ℃
2. Inlet pressure: 0.7-1.0mpa
3. Air dew point: - 40 ℃
4. Regeneration gas consumption: ≤ 2%
5. Ambient temperature: ≤ 45 ℃
6. Cooling water temperature 0-32 ℃
7. Cooling water pressure: 0.2-0.55mpa
8. Regular 8-hour cycle
8. Installation method: indoor, without foundation, concrete ground leveling, reserved maintenance and operation space
9. Adsorbent: activated alumina, molecular sieve
10. Power supply: 220-1ph-50hz
11. Users can optionally configure customized products, and consult our technical service department for detailed technical parameters
Design features:
1. Pure logic control, friendly human-machine interface, automatic continuous display of double tower working condition
2. It adopts high temperature resistant double eccentric pneumatic butterfly valve, stainless steel anti-corrosion valve body and stem, with long service life, valve position maintenance, fault alarm and feedback functions
3. The supporting ceramic ball is used at the bottom of the adsorption tower, which makes the air distribution more uniform, effectively prevents the failure of the adsorbent bubble water and prolongs the service life of the adsorbent
4. Scientific air distributor to reduce pressure loss, high utilization rate of desiccant and low risk of wear
5. The stainless steel cooler has good cooling effect and strong corrosion resistance
6. The centrifugal gas-liquid separator has good separation effect and small pressure loss
7. Manual drainage and intelligent drainage system
8. Complete set of stainless steel power supply pipeline is provided as standard
9. Frequency conversion with delayed adsorption technology is more energy-saving (optional)
10. PLC control system has RS485 serial communication interface, which can meet the communication requirements of users (optional)
中文
ENGLISH